The Ideal Solution For Deeply Cracked Concrete Repair
Preparation is the key to a perfect finish, and ensuring all cracks, holes and spalled areas are filled is an essential step. Deepfill is the ideal choice for deeper cracks where traditional concrete repair kits aren’t up to the job and for general concrete hole repair. Prepare the hole by removing all dust, grease and dirt then apply Tackprime before using this 3 part concrete repair epoxy resin to effect the repair. Deepfill acts as a concrete repair patch up to 50mm in thickness for larger areas and 100mm for smaller cracks.
Use as a Protective Screed
As well as repairing cracked concrete floors and walls, Deepfill concrete repair resin can be used as a protective screed on floor areas subject to impact, abrasion and chemical spillage. This makes it ideal for use in locations such as loading bays or bunded areas.
Can Also Be Used as Bedding Mortar
Alternatively, you can use Deepfill as a thick section epoxy bedding mortar for kerb stones, paving or brickwork etc.
Find Out More
Not sure if Deepfill is right for your project, or just want to know more about our range of concrete repair kits? Contact our advice line on 0191 389 7067 and talk to a specialist.
- Colour: Natural or Concrete Grey
- Density: 2200kg/m³
- Pot Life: 50-60 minutes @ 20°C
- Adhesion to concrete: 3.6MPa (concrete failure)
- Compressive Strength: 64MPa
- Chemical resistance: Excellent resistance to dilute acids and alkalis, oil, petrol, diesel, vegetable oils, inorganic salts, and cleaning fluids.
Reprotec Deepfill is supplied in 25kg packs.
A 25kg pack of Reprotec Deepfill yields 11.4 litres of material, sufficient for 1.14m² @ 10mm thickness.
For filling voids use the table below as a guide.
|1 Linear metre long x 100mm wide x 100mm deep||One Unit of Reprotec Deepfill required|
|2 Linear metres long x 100mm wide x 50mm deep||One Unit of Reprotec Deepfill required|
|4 Linear metres long x 100mm wide x 25mm deep||One Unit of Reprotec Deepfill required|
|10 Linear metres long x 100mm wide x 50mm deep||Five Units of Reprotec Deepfill required|
|20 Linear metres long x 100mm wide x 25mm deep||Five Units of Reprotec Deepfill required|
|100 Linear metres Long x 50mm wide x 25mm deep||Thirteen Units of Reprotec Deepfill required|
Apply a coat of Reprotec Tackprime by brush or roller at a nominal rate of 3.5 to 7.0m²/kg, depending upon surface profile.
The use of mechanical, forced action mixer such as a Creteangle, is strongly recommended.
However, as long as the resin components are mechanically mixed, old fashioned "elbow grease" will be effective, mix until a uniform material is achieved.
** Top Tip - Always mix the resins together first -- never, never try to mix all 3 components in one mix **
Pour the contents of the CURING AGENT container into the BASE container and mix thoroughly with a slow speed paddle.
The mixed resins shall be poured into a mixing vessel, (Creteangle bucket or similar), and the AGGREGATE added steadily whilst the mixer is in motion. Mix for 2-3 minutes until a uniform material is achieved.
Reprotec Deepfill shall be applied whilst the primer is still ‘tacky’ i.e. within 2 hours of application.
The material should be tamped and trowelled to ensure good compaction and a tight finish.
Minimum application thickness is 10mm; maximum application thickness is 50mm for large areas.
Note: up to 100mm thickness may be applied in small patches.
- As a deep section protective screed for floor areas subject to impact, abrasion and chemical spillage.
- As an economical, fast curing in-fill screed/mortar prior to the application of the final floor finish.
- Ease of application
- Fast curing characteristics
- Hard wearing and durable
- Taint free
- Frost resistant and impervious to water
- Negligible shrinkage even in thick section